Path: EDN Asia >> Design Centre >> Power/Smart Energy >> Pairing supercap with small energy-harvesting source
Power/Smart Energy Share print

Pairing supercap with small energy-harvesting source

13 Sep 2012  | Pierre Mars

Share this page with your friends

The supercapacitor capacitance and ESR should also allow for aging. Supercapacitors slowly lose capacitance and increase ESR over time. The aging rate depends on cell voltage and temperature. Designers should select initial capacitance and ESR so that the end-of-life capacitance and ESR can support the applications.

Supercapacitor charging
A discharged supercapacitor looks like a short circuit to an energy source. Fortunately, many energy-harvesting sources, such as solar cells and microgenerators, can drive into a short circuit and directly charge a supercapacitor from 0V. ICs to interface energy sources, such as piezoelectric or thermoelectric energy, must be able to drive into a short circuit to charge a supercapacitor.

The industry has invested much effort in MPPT (maximum-peak-power tracking) to most efficiently draw power from energy-harvesting sources. This approach is applicable when charging a battery that must charge at constant voltage. The battery charger is typically a dc/dc converter that is a constant-power load to the energy source, so it makes sense to draw that power at the most efficient point using MPPT.

In contrast to a battery, a supercapacitor need not charge at a constant voltage but charges most efficiently by drawing the maximum current the source can supply. Figure 2 shows a simple and effective charging circuit for cases in which the open-circuit voltage of a solar-cell array is less than the supercapacitor's rated voltage. The diode prevents the supercapacitor from discharging back through the solar cell if it goes dark. If the energy source's open-circuit voltage is greater than the supercapacitor's voltage, then the supercapacitor requires overvoltage protection using a shunt regulator (figure 3). A shunt regulator is an inexpensive and simple approach to overvoltage protection, and, once the supercapacitor fully charges, it does not matter whether the excess energy dissipates.

The energy harvester is like a hose with an endless supply of water filling a barrel, which is analogous to a supercapacitor. If the hose is still running once the barrel is full, the water may overflow. This situation differs from that of a battery, which has a limited energy supply and thus would require a series regulator.

In the circuit in figure 2, the supercapacitor, at 0V, draws short-circuit current from a solar cell. As the supercapacitor charges, the current decreases, depending on the solar cell's voltage/current characteristic. The supercapacitor always draws the maximum current it can, however, so it charges at the highest possible rate. The circuit in figure 3 uses the TLV3011 solar cell because it integrates a voltage reference, draws only approximately 3-µA quiescent current, and is an open-drain cell so that the output is open-circuit when the regulator is off. This circuit uses the BAT54 diode because it has a low forward voltage at low currents—that is, the forward voltage is less than 0.1V at a forward current of less than 10µA.

Microgenerators are ideal for industrial-control applications, such as monitoring rotating machinery, because by definition they will vibrate when they are operating. Figure 4 shows the voltage-current characteristic of a microgenerator, which is similar to that of a solar cell and which delivers maximum current into a short circuit. A microgenerator also includes a diode bridge, which prevents the supercapacitor from discharging back into the generator, leading to a simple charging circuit (figure 5).

The open-circuit voltage is 8.5V, requiring a dual-cell supercapacitor, such as the CAP-XX HZ202, which operates at 5.5V. A shunt regulator provides overvoltage protection, and a lowcurrent active-balance circuit ensures even distribution between the cells. Linear Technology, with its LT3652, LTC3108, and LTC3625 ICs, and Texas Instruments, with its BQ25504, charge supercapacitors from energy-harvesting sources.

Leakage current
Because some energy harvesters deliver only a few microamps, leakage current becomes important. Supercapacitors can have leakage currents of less than 1µA, making them suitable for energy-harvesting applications (figure 6).


 First Page Previous Page 1 • 2 • 3 Next Page Last Page


Want to more of this to be delivered to you for FREE?

Subscribe to EDN Asia alerts and receive the latest design ideas and product news in your inbox.

Got to make sure you're not a robot. Please enter the code displayed on the right.

Time to activate your subscription - it's easy!

We have sent an activate request to your registerd e-email. Simply click on the link to activate your subscription.

We're doing this to protect your privacy and ensure you successfully receive your e-mail alerts.


Add New Comment
Visitor (To avoid code verification, simply login or register with us. It is fast and free!)
*Verify code:
Tech Impact

Regional Roundup
Control this smart glass with the blink of an eye
K-Glass 2 detects users' eye movements to point the cursor to recognise computer icons or objects in the Internet, and uses winks for commands. The researchers call this interface the "i-Mouse."

GlobalFoundries extends grants to Singapore students
ARM, Tencent Games team up to improve mobile gaming


News | Products | Design Features | Regional Roundup | Tech Impact