Path: EDN Asia >> Design Ideas >> Test & Measurement >> Measuring resistance in micro-ohms range
Test & Measurement Share print

Measuring resistance in micro-ohms range

17 Jan 2013  | Moshe Gerstenhaber, Mark Champion

Share this page with your friends

Numerous applications require the measurement of very low resistances, including but not limited to fuse integrity analysis, relay characterisation, and superconductor evaluation. There is a wide range of commercially available equipment designed for this task, but these units are prohibitively expensive and cannot be practically integrated into many applications outside the laboratory. A common low-cost and compact method of measuring resistance is to inject a known dc current into the unknown resistor, measure the resulting voltage and calculate the resistance using Ohm's law. Unfortunately, for very low resistances, the current required to generate a voltage sufficiently distinguishable from the surrounding noise becomes impractically large.

Figure 1: The AD8253 is configured in transparent gain mode, allowing the gain to be manually set by the user according to Table 1.

Figure 1 is a schematic of a complete, low-cost, software-programmable lock-in amplifier designed to measure resistances in the micro-Ohm range. An ac voltage is generated by switching current into the unknown resistance. The 1 mA current pulse is generated by using an analogue switch (ADG436) to alternately apply 10V (from the ADR01 precision reference) and ground to the series connection of 10 kΩ and the unknown resistance. The resulting ac voltage, which is imperceptibly small, is then applied to an AD8228 instrumentation amplifier configured in a gain of 100. The low noise of the AD8228 make it well-suited for a first gain stage. Following the AD8228 is an AD8253 software-programmable gain instrumentation amplifier which can be configured in gains of 1, 10, 100, or 1000 depending on the size of the resistance being measured. In

figure 1, the AD8253 is configured in transparent gain mode, allowing the gain to be manually set by the user according to table 1. The system gain is extremely stable over temperature due to the low gain drift of the AD8228 and AD8253. To extract its amplitude information, a balanced demodulator (AD630) synchronously rectifies the amplified signal. An active three-pole low-pass filter using an AD820 then rejects all out-of-band frequencies, while passing the in-band signal of interest with a transfer function of 50 mV/mΩ at maximum system gain.

The system is completely self-contained, and the user only needs to provide a ±15V supply. A 1kHz oscillator, constructed from common low-cost digital ICs, creates the CLK signal that controls the excitation and demodulation sections of the system, where the 5V supply for these ICs is obtained from the 15V rail using an ADR5045 shunt regulator.

Figure 2: The output voltage of the system for various lengths of 18 AWG copper wire has a resistance of 213.58µΩ/cm, as measured in the laboratory.

The output voltage of the system is linear over the entire range as can be seen above in figure 2.

Figure 3: The measurement error of the system, where the noise in the curve is due to the human error in placing the measurement leads, and the slope of the curve is due to a slight system gain error.

Figure 4: The linearity of the system is demonstrated by the output voltage of the system as the measurement leads are placed across 1, 2, 4, 8, and 16 cm lengths of wire.

The linearity of the system is further demonstrated by figure 4.

About the authors
Moshe Gerstenhaber and Mark Champion are from Analog Devices.

To download the PDF version of this article, click here.




Want to more of this to be delivered to you for FREE?

Subscribe to EDN Asia alerts and receive the latest design ideas and product news in your inbox.

Got to make sure you're not a robot. Please enter the code displayed on the right.

Time to activate your subscription - it's easy!

We have sent an activate request to your registerd e-email. Simply click on the link to activate your subscription.

We're doing this to protect your privacy and ensure you successfully receive your e-mail alerts.


Add New Comment
Visitor (To avoid code verification, simply login or register with us. It is fast and free!)
*Verify code:
Tech Impact

Regional Roundup
Control this smart glass with the blink of an eye
K-Glass 2 detects users' eye movements to point the cursor to recognise computer icons or objects in the Internet, and uses winks for commands. The researchers call this interface the "i-Mouse."

GlobalFoundries extends grants to Singapore students
ARM, Tencent Games team up to improve mobile gaming


News | Products | Design Features | Regional Roundup | Tech Impact