Path: EDN Asia >> Design Ideas >> IC/Board/Systems Design >> Creating a low-leakage rectifier
IC/Board/Systems Design Share print

Creating a low-leakage rectifier

10 May 2013  | Martin Tomasz

Share this page with your friends

You can integrate a carefully selected op amp, a low-threshold P-channel MOSFET, and two feedback resistors to make a rectifier circuit with less forward drop than a diode (figure 1). The rectified output voltage powers the active circuitry, so no additional power supply is necessary. The circuit's quiescent current is lower than most Schottky diodes' reverse-leakage current. This circuit provides active rectification at voltage drops as low as 0.8V. At lower voltages, the MOSFET's body diode takes over as an ordinary diode.


The op-amp circuit turns on the MOSFET as a forward voltage develops between the input and the output voltages, according to the following equation:


where VGATE is the MOSFET's gate drive, VIN is the input voltage, and VOUT is the output voltage. You can relate the input and the output voltages to the MOSFET's drain-to-source and gate-to-source voltages, according to the following equations:


where VDS is the drain-to-source voltage and VGS is the gate-to-source voltage. Combine these equations to relate the MOSFET's gate drive to a function of the drain-to-source voltage:


If you make R2 12 times larger in value than R1, a 40-mV voltage drop across the MOSFET's drain-to-source voltage is sufficient to turn on the MOSFET at low drain currents (figure 2). You could choose a higher ratio to further reduce the voltage drop within the limits of the op amp's worst-case input-offset voltage of 6 mV. The op amp is powered from output-reservoir capacitor C1. The amplifier has rail-torail inputs and outputs and no phase inversion when operating near the rails. The amplifier operates at power-supply voltages as low as 0.8V. You directly connect the op amp's noninverting input to the VDD rail and the amp's output to the gate of the MOSFET. The circuit consumes slightly more than 1µA when actively rectifying a 100Hz sine wave, less current leakage than that of most Schottky diodes. The BSH205 supports milliamp-level currents at a gate-to-source voltage of 0.8V.


The op amp's bandwidth limits the circuit to lower-frequency signals. At bandwidths higher than 500Hz, the amplifier's gain begins to decline. As the signal frequency increases, the MOSFET remains off, and the body diode of the MOSFET takes over the rectification function. An input with a fast fall time could potentially drag the output with reverse current through the MOSFET. However, for small currents, the MOSFET operates in its subthreshold range.


The amplifier quickly turns off due to the exponential relationship of the gate-to-source voltage to the drain-to-source current in the subthreshold range. The limiting factor is the amplifier's slew rate of 1.5V/msec. As long as you don't load the circuit so heavily that you drive the MOSFET into its linear range, reverse currents won't exceed forward currents.

You can use the circuit in a micropower solar-harvesting application (figure 3). Depending on the light, the BPW34 cells generate 10 to 30µA at 0.8 to 1.5V. The active-diode circuit rectifies the peak harvested voltage in conditions of rapidly changing light and minimises reverse leakage to the cells.


About the author
Martin Tomasz is from Sageloop Designs.


To download the PDF version of this article, click here.




Want to more of this to be delivered to you for FREE?

Subscribe to EDN Asia alerts and receive the latest design ideas and product news in your inbox.

Got to make sure you're not a robot. Please enter the code displayed on the right.

Time to activate your subscription - it's easy!

We have sent an activate request to your registerd e-email. Simply click on the link to activate your subscription.

We're doing this to protect your privacy and ensure you successfully receive your e-mail alerts.


Add New Comment
Visitor (To avoid code verification, simply login or register with us. It is fast and free!)
*Verify code:
Tech Impact

Regional Roundup
Control this smart glass with the blink of an eye
K-Glass 2 detects users' eye movements to point the cursor to recognise computer icons or objects in the Internet, and uses winks for commands. The researchers call this interface the "i-Mouse."

GlobalFoundries extends grants to Singapore students
ARM, Tencent Games team up to improve mobile gaming


News | Products | Design Features | Regional Roundup | Tech Impact