Path: EDN Asia >> Design Ideas >> Test & Measurement >> Circuits guard outputs against over-voltage
Test & Measurement Share print

Circuits guard outputs against over-voltage

04 May 2016  | Dimitri Danyuk

Share this page with your friends

In test-and-measurement applications, you must have over-voltage protection for the output terminals of amplifiers, power supplies, and similar components. The conventional way to accomplish this task is to add series resistors with the output node along with the clamping diodes to power-supply rails or other threshold voltages (reference 1 and figure 1). This resistor significantly reduces current-output capability and the output-voltage swing with low-resistance loads. The alternative approach is to use fuses or other current-limiting devices, which precede these clamps' high energy-absorption capability. The circuit in figure 2 works as a bipolar current source when the voltage drop across source resistor R6 becomes larger than the gate-threshold voltage of depletion-mode MOSFETs Q1 and Q2, thus limiting the current through the clamping diodes (reference 2). The drawback of this approach is high power dissipation on series components during the overload condition.


Figure 1: The conventional way to provide over-voltage protection is to add series resistors with the output node along with the clamping diodes to power-supply rails or other threshold voltages.


A reasonable approach disconnects the amplifier-output node from the output terminals for the period when the overload voltage exists on output terminals. Engineers for decades have used such serial disconnection by means of electromechanical relays in audio power amplifiers but for a different reason: loudspeaker protection. SSRs (solid-state relays), including optoelectronic, photovoltaic, OptoMOS, and PhotoMOS devices, suit the task of load disconnection at moderate current levels because of galvanic isolation between the control and the load pins (reference 3).


Figure 2: This circuit works as a bipolar-current source when the voltage drop across source resistor R6 becomes larger than the gate-threshold voltage of depletion-mode MOSFETs Q1 and Q2, thus limiting the current through clamping diodes.


The series-protection circuit of figure 3 disconnects the amplifier-output terminal using a series-connected, high-voltage SSR. Raising the output voltage above the positive-reference-voltage or below the negative-reference-voltage threshold causes either the IC2 or the IC3 comparator to change its output state and turn off SSR IC4 through AND logic element IC5. Figure 4 shows the simple circuit realisation of this approach.


Figure 3: This series-protection circuit disconnects the amplifier-output terminal using a series-connected, high-voltage SSR.


Figure 4: This circuit requires only a couple of external components to use an SSR for output-over-voltage protection.


The circuit in figure 4 requires only a couple of external components to use an SSR for output-over-voltage protection. Rising over-voltage turns off both transistors in IC2, interrupting current flow through the control LED of IC3. Relay IC3 opens, protecting the amplifier and clamping diodes. The circuit was tested with a handful of Clare, Matsushita Electronic Works, and Panasonic SSRs with and without internal current protection. The power-supply rails are ±15V; R10, R11, and R12 set the triggering levels and are equal to ±16V. Omitting R11 shifts the triggering levels to ±14.5V. The SSR turn-off delay in protection-circuit operation is 100 to 200µsec for relays with 0.5V over-voltage protection and becomes slightly shorter with higher over-voltage. Note that the peak current through clamping diodes can be rather high with low-on-resistance SSRs.


References
1. Steele, Jerry, "Protect Those Expensive Power Op Amps," Electronic Design, Jan 31, 1991.

2. "±500V Protection Circuit," Application Note AN–D11, Supertex Inc, Aug 14, 2000.

3. Stitt, R Mark, and David Kunst, "Input Overload Protection for the RCV420 4-20MA Current-Loop Receiver," Burr-Brown, Application Bulletin AB-013, July 1990.

4. "Fault-Tolerant Analog Switches," Application Note 745, Maxim Integrated Products Inc, March 25, 2001.


About the author
Dimitri Danyuk contributed this article.


This article is a Design Idea selected for re-publication by the editors. It was first published on October 11, 2007 in EDN.com.




Want to more of this to be delivered to you for FREE?

Subscribe to EDN Asia alerts and receive the latest design ideas and product news in your inbox.

Got to make sure you're not a robot. Please enter the code displayed on the right.

Time to activate your subscription - it's easy!

We have sent an activate request to your registerd e-email. Simply click on the link to activate your subscription.

We're doing this to protect your privacy and ensure you successfully receive your e-mail alerts.


Add New Comment
Visitor (To avoid code verification, simply login or register with us. It is fast and free!)
*Verify code:
Tech Impact

Regional Roundup
Control this smart glass with the blink of an eye
K-Glass 2 detects users' eye movements to point the cursor to recognise computer icons or objects in the Internet, and uses winks for commands. The researchers call this interface the "i-Mouse."

GlobalFoundries extends grants to Singapore students
ARM, Tencent Games team up to improve mobile gaming


News | Products | Design Features | Regional Roundup | Tech Impact